Aardvark Embedded Solutions Ltd Support Forum

Hello, we have Paylink system with NRI currenza c2 (MDB) and iPRO-RC (ID003). There are two issues that we need to solve: 1) We have iPRO set to recycle 100 and 500 CZK banknotes, after payout of 618 CZK iPRO stops accepting banknotes. See log: 15:10:42.032 ID-003: Enable acceptance 15:10:59.611 04:...

We resolve counters problem on NRI currenza c2 with auto flow-up settings which set counters to predefined values.
But we have similar issue with iPRO-RC. Is it possible to set number of banknotes in recycler after filling cassete manually?

Is it possible to set number of coins in dispenser (single tube) manually?

I asked Crane for help, but they redirected me to Suzo Happ and I'm still waiting for response. I think that problem is in settings of coin changer because its internal inventory (in menu) is showing similar numbers, which are tranfered to Paylink. When I insert empty cassete, it reports 0 coins cor...

Hello. we are trying to setup Paylink with coin changer NRI currenza c2 blue, but we have problem with coin counters after refilling cassete directly (remove, fill tubes and return to changer). Counters are always higher than real number of coins. It causes problems, because system reports that coin...

There was problem in interface settings, it works now...

We received JCM iPRO unit for testing with PayLink, but we have problem make them communicate. When we connect unit to PC with USB cable we received these values from JCM Tool Suite: Flash ROM: U(CZE)100-SH2-RC ID003-05 V190-20 30SEP14 Protocol ID: 003 We have serial cable from iPRO that ends with C...

Brand is not important, we want to use PayLink as controller and have reliable system.

I have question about your recommendation for note recycler that is fully supported by PayLink, because we will also need some device that have bigger recycling capactity than VEGA-RC.

I received support from JCM, did correct setup (SW4 on DS2) and key is OK!

Vega is accepting notes (4 from 6 types) and paying out.

Thank you for your help.

I followed you instructions and message from VEGA is different, but result is same. 07:37:29.752 ccNote: Encyption Information 07:37:29.752 : Protocol: 0, Encryption: 101, 07:37:29.752 : Sizes: 24 / 64 / 64, 07:37:29.752 : No Key available 07:37:29.814 DP: ccNote Status to 65 07:37:29.814 DP: ccNote...

Currenza starts working both ways after restart, so it is done. I connect VEGA with recycler through ccTalk cable and set protocol mode to ccTalk (Encrypted) according to manual. There is also action to init encryption code - set it to VEGA serial number, but this number is 10 digits long and PayLin...

OK, I will contact JCM about VEGA connection options. But VEGA works for me on ID003, but not using recycler, is it possible make it work? There is also option to use MDB on VEGA, but I don't know if it possible to combine 2 MDB devices on PayLink. Similar problem I have with currenza coin changer o...

Now, I have semi-working configuration: NRI currenza c2 connected to (1): Protocol MDB on connector MDB Changer at 8 Log: 12:58:22.780 MDB: Manu: NRI, Ser # 10121807-001, Model C2Pv0 3 455, diag. avail, Extended Payout 12:58:22.827 MDB Tube@9: for 100 - reported coins 0=>0 12:58:22.827 MDB Tube@10: ...

OK, it means that NRI currenza c2 with USB cannot be controlled with PayLink, for now.

In case of VEGA, that is multi-protocol (DIP switch selectable ID-003, ccTalk or MDB), which one is best for communication with PayLink?